Talk:Sleeve valve

Modern Usage

"A recent SAE paper deals with a high speed,..." I think a reference should be given which would obviate the "recent" - an increasingly vague term as the years go by. Dawright12 (talk) 10:25, 2 May 2011 (UTC)

• SAE paper 2003-01-2275 by Alvin Lowi, Jr. Anyway, there are not too many SAE papers on the Sleeve-Valve subject, if you enter the sae.org website, and look into the publications using their internal search feature, it's quite easy.

Sleeve Valves today

I am currently researching sleeve valve engines. Is there any body out there doing anything new with sleeve valves?

I would also like to hear from anyone with first hand experiance of the Bristol sleeve valve engines; i.e. pilots or engineers or those on the production line.

How reliable were they and were they realy oil thirsty?

---

I didn't notice the post above until just now, and since you didn't register I don't have an account to reply to. Hopefully you'll see this.

The "oil thirsty" issues are not theoretical, they are entirely practical. Basically engines are nowhere near "pefectly circular" and as a result pistons to not fit cleanly into the cylinder. Instead the piston rings are placed around the piston and run until they scrape off the irregularities on the cylinder, which is deposited in the oil. This is called "breaking in" an engine, and you have to change the oil very soon after it is new.

With a sleeve valve the piston rings do not run on the cylinder wall, but the sleeve. This means that they scrape off a repeating N pattern in the sleeve as the piston moves up and down, so there is always somewhere on the sleeve that is not sealed. The oil blows past this hole and is burned.

However that was 50 years ago when a milimeter was considered the height of accuracy. With modern construction techniques and materials engines don't even have a breaking in period any more. The same techniques would "solve" the problems of the sleeve valve design, but there simply isn't any money in it.

Maury 00:15, 28 Dec 2003 (UTC)

<<However that was 50 years ago when a milimeter was considered the height of accuracy. >>

That's just rubbish, a mm is 39 thou, the Bristol sleeves were produced to 10ths of a thou, with a very carefully conrolled circularity

Additionally, despite the 'N' pattern, there is a very big advantage of sleeve vales rotating when at extents of the stroke, which is that the oil film never breaks down at TDC or BDC, and this has recently been acknowledged, there being a sleeve patent 'just for this purpose', of reducing sealing problems at TDC! —Preceding unsigned comment added by 82.21.211.115 (talk) 18:51, 20 June 2009 (UTC)

The issue with break in was traditionally cost. There was probably a time when break in hadn't been considered and it certainly wasn't a disadvantage. Later break in allowed engines for auto use to be made with less precision and lower unit cost. Today the machining cost isn't much of an issue so engines are made out of the box ready and acurate machining would be less of a disadvantage then it was in the past.

Most sleeve valve aero engines used a dry sump oil system with a separate oil tank, so oil consumption wasn't a problem, as one could just fit a bigger oil tank. A gallon or two of extra oil makes no meaningful difference when the normal oil capacity is measured in tens of gallons anyway. — Preceding unsigned comment added by 80.7.147.13 (talk) 11:43, 6 April 2014 (UTC)

FYI in the Avro Lancaster each engine had a 37.5 gallon oil tank. The Hawker Typhoon had a 16 gallon one, the Hawker Sea Fury one of fourteen gallons. — Preceding unsigned comment added by 2.29.18.221 (talk) 14:51, 15 November 2015 (UTC)

Bristol Centaurus oil consumption figures: at Max Cruising rpm = 10 pints per-hour, falling to 4 pints per-hour at lower rpm: [1] — Preceding unsigned comment added by 95.150.11.216 (talk) 16:13, 21 March 2016 (UTC)

Sleeve valve

is there anyone who has a drawing of a sleeve valve

Found a good description with drawings here: [2]

GalFisk

Why is it that I always seem to be able to only find undersquare engines (bore diameter less than the piston travel) when looking at sleeve valve engines? Does the sleeve valve engine only allow low speed operation or require excessive stroke to function well? Would a high speed, substantially oversquare sleeve valve engine possibly exist? -Dave —Preceding unsigned comment added by Mrskyking737 (talk • contribs) 02:38, 3 July 2009 (UTC)

• These days most engines had a longer stroke than bore, this arrangement seems giving low speed torque and fuel economy advantages, and perhaps it was also more adapted for the existing fuels, today fast running engines use having square and oversquare designs, bore equal or bigger than stroke, for better high speed performance and low wear, as a short stroke engine has a lower top piston speed. The author of the book on Continental engines and people points that sleeve valves were not more expensive, but even easier and cheaper to produce, Hewland claims any device able to do round machining is good enough for making sleeves, but this has to be confirmed in the engine makers using SSV and Knigth engines, they were not many, but them all ceased research and production of this engines around the beginning and end of WWII. The flying boat Saunders-Roe Princess was probably the last big airplane that envisaged the use of SSV engines for commercial use, and some two engine transport airplanes from the spanish airplane maker CASA installed Bristol SSV engines in the immediate post-war period; no more data from the Mike Hewland and other british research conducted in the 70's and 80's is available. Hewland pointed having made several SSV related discoveries susceptible of patent protection, but he applied for no patents, even when he stated that if somebody wanted making him an offer for all their research on SSV engines, he will consider it. The heirs of the M Hewland racing gearbox business don't provide additional information about the subject of SSV engines besides what is pointed in this Wikipedia article.--Jgrosay (talk) 13:54, 22 April 2012 (UTC)

Cleanup

How about starting with some basic things like telling us at least something about what it is first, before you get into advantages and history? Gene Nygaard 07:29, 7 October 2006 (UTC)

Referencing style

Body text has inline references (Harvard style I think) which could be transferred to the wiki style, as the data is included. I'll wait for any objections here, in case there is a specific reason for the unusual style

sleeve, separate openings for I and E

or just one? CorvetteZ51 14:05, 16 July 2007 (UTC)

I'm not sure if this is universally true, but for one engine with which I'm slightly familiar, there were some (I forget the number) dedicated openings in the sleeve for inlet OR exhaust and one opening that opened inlet and exhaust in turn. (If I can find out more, I'll add it). In fact, the drawing linked above shows exactly this layout. 217.205.121.71 18:12, 17 August 2007 (UTC)

Port size query

"the speed at which air can enter and exit the cylinder is defined by the size of the duct leading to the cylinder and varies according to the cube of the RPM"

Is this true?

Picture

This article really needs a diagram to explain the mechanics involved at a glance. Drutt (talk) 16:27, 27 June 2008 (UTC)

Decline of the Sleeve Valve

The single sleeve valve design really came about as a response to deficiencies in the combustion chamber design of poppet valve piston engines of the '20s and early '30s. Specifically, the knock limit of spark-ignited (SI) engines. Once the process of combustion detonation became more understood, the design deficiencies in the poppet valve combustion chamber were corrected and the sleeve valve fell out of favor. The main reason for this was that the sleeve valve was very difficult and expensive to mass produce, its oil consumption was high, and it had relatively poor durability. As for flow characteristics, the port-time area of a single sleeve valve is really no better than a good 4-valve poppet design. Riff raff99 (talk) 01:48, 28 December 2008 (UTC)

<<and it had relatively poor durability. >>

Mmm! The Bristol Hercules sleeve-valve engines were the first to achieve 3,000 hrs MTBO (Mean Time Between Overhaul). This was towards the end of the war and subsequently the Centaurus achieved a similar rating - postwar in civil use. Equivalent power poppet-valve engines would be more like 1,000 hrs at that time @@

<<As for flow characteristics, the port-time area of a single sleeve valve is really no better than a good 4-valve poppet design.>>

Maybe not, but there's more to it than that, as the Sabre and Crecy designs had hardly been fully developed at the time of their demise (by gas-turbines, not poppet-valved recips). Both were capable of phenomenal bench (specific) outputs by 1945/46. And all other RR (military) new designs were by then sleeve-valves (Exe, etc).

[HM]

 —Preceding unsigned comment added by 82.21.211.115 (talk) 18:57, 20 June 2009 (UTC) 

Sleeve valve engines are not prone to the valve bounce which limits the RPM of a poppet valve engine, so they can therefore be run much faster, making them more efficient - the poppet valve RR Merlin being run at 3,000 RPM and the sleeve valve Napier Sabre being run at 3,900 RPM and above. Sleeve valve engines are also mechanically quieter and have considerably less vibration due to the absence of the normal reciprocating valve gear. The sleeve valve also robs the engine of less power, the poppet valve engine needing to operate against the force of the valve springs, a not inconsiderable force in a large, multi-cylinder engine. The sleeve valve was only discontinued because of the demise of the need for ever more-powerful military piston aero-engines. If you want the highest possible power-to-weight ratio then sleeve valves are the way to go, which is one of the reasons that Bristol and Napier used them, the later Hercules and Centaurus being as reliable as any poppet valve engine, the Sabre, after the initial development problems had been solved, likewise. —Preceding unsigned comment added by 213.40.249.111 (talk) 17:04, 28 December 2009 (UTC)

The publication Torque Meter and the website by the Aircraft Engine Historical Society (www.enginehistory.org) contains detailed discussions on the advantages and disadvantages of Burt-McCollum SV engines, including the way Bristol engines were produced, this magazine has a very reasonable cost —Preceding unsigned comment added by Jgrosay (talk • contribs) 10:55, 22 March 2010 (UTC)

Picture in a 1942 issue of Flight showing the far fewer parts in a Bristol Hercules sleeve valve radial engine cylinder and head compared to a conventional poppet valve engine of similar type, here: [3]

A 1939 Flight article "Sleeve-Valve Development" by Roy Fedden here: [4] — Preceding unsigned comment added by 80.7.147.13 (talk) 16:43, 2 March 2014 (UTC)

"As for flow characteristics, the port-time area of a single sleeve valve is really no better than a good 4-valve poppet design." - no manufacturer was ever able to produce a two-row radial with four poppet valves per-cylinder. They only managed two valves per-cylinder. That was one of the reasons why Bristol went to sleeve valves. — Preceding unsigned comment added by 95.149.53.233 (talk) 23:03, 15 March 2016 (UTC)

All the large non-sleeve valve radial aero engines were two-valve per-cylinder. The use of sleeve valves allowed more power per cylinder or, alternatively, the use of lower octane fuel for the same power. — Preceding unsigned comment added by 95.149.172.235 (talk) 18:49, 12 November 2018 (UTC)

Some figures

The 1953 Edition of the H Ricardo book on High-Speed Internal Combustion Engines tells in detail the history of materials used for both sleeve and cylinders, in liquid-cooled and air-cooled cylinders, and has also a section on petrol two-stroke engines, not suitable for automobile use because of instability below 40% of rated maximal power, and deals also with the issue of compression ignition engines. I fear breaking some copyright, but I'll summarize my reading of the chapter, sorry, I'm not engineer.

Around 1922, the sleeve operating mechanism was changed from a white metal spherical joint, to bronze or aluminum. Sleeves were of cast iron, and then of steel, and pistons of aluminum. The S.V. working clearance was set in 0.0005 in. per inch of cylinder diameter (Figure checked). As long as the clearance between sleeve and cylinder was kept narrow, the oil film acted as an adequate mean to transmit heat from the piston to the cylinder wall. In 1925, aluminum cylinders were tested, and he tells that with this kind of material for cylinders, a carbon steel valve was good for small cylinders. For liquid cooled cylinders of 5 in. diameter or less, aluminum alloy with a cast iron or carbon steel sleeve worked well. Later on, he states that cylinders of silicon-aluminum alloys with sleeves of austenitic irons and steels looked promising. For air-cooled engines of 5 1/2 in. bore, he used silicon-aluminum alloy and a sleeve of austenitic steel, giving a difference in thermal expansion of 1.3:1. Austenitic steel proved bad, and a procedure was found of improving the surface of the bore of sleeve by rolling and shot-blasting. With a cast austenitic iron sleeve, they got a S.F.C. of 0.39 lb per B HP hour.

When Bristol began to behave with a serious interest, they found that the austenitic-steel sleeve could be nitrogen hardened, but in the process, some sleeve distorsion was produced, and the very smooth and hard surface gave lubrication troubles, their solution was finding means to massaging the sleeve into truth after hardening, and a coarse honing process to break up the very smooth surface, that sir Harry Ricardo calls: "Satin finish". (Wankel engines had the same problem, solved among other ways with the Nikasil coating procedure, also the addition to lubricating oil of a solid state lubricating agent as Molybdenum Bisulfide -MoS2- is of help in maintainig lubrication under extreme Internal Combustion Engine's operating conditions).

An article in a book about machining says that sleeves were machined using a solid inner cast while machining the outer side, plaster was used for this purpose, and a similar procedure while machining the inner part. Centrifugally cast nitrogen hardened austenitic steel sleeve with control over the manufacturing limits made unnecessary to use a silicon-aluminum alloy for cylinders. For the cylinder head, called 'Junk head', a composite copper-steel, cooled head was developed. A V12 version of S-S-V engine attained an S.F.C. of 0.38 lb. B HP hour. The appropriate sleeve strike was set in 30% of piston stroke, but in another publication, H Ricardo speaks about Sleeve stroke not exceeding 25% of piston stroke. A shorter sleeve stroke would give a greater inlet area, but reduced exhaust port area, and the opposite. In 2-stroke engines, the effective length of piston was determined to be equal to piston stroke less sleeve stroke, more or less 70% of piston stroke, and in these engines, the sleeve thickness was 0.125 in.

An experimental unit used cast-iron cylinder with carbon steel sleeve, and also an open-ended carbon steel sleeve in an aluminum cylinder was considered. The compression-ignition engines used an open end sleeve, that in fact acted as another piston, participating in the transmission of the power to the crankshaft. Their 2-stroke engines had an oil use of 2 pint per hour, with dimensions of 4.8 in by 5.5 in. Also, a 0.55 carbon cast steel sleeve, directly on silicon-aluminum alloy cylinder was tested, that had the advantage of being machined from centrifugal steel castings, but this proved good for low B.M.E.P., if BMEP was above 200 x 2 lb. per sq. in., nitrogen hardened austenitic steel sleeves, with satin finish, were required for an air-cooled 4-cycle S-V engine. Bill Gunston, in his book on Development of Piston Aero Engines, points that it took R Fedden testing literally thousands of combinations of alloys and production methods to make flawless sleeves by centrifugal casting and then making them perfectly cylindrical.

Nitrided sleeves had a life between 2'000 and 4'000 hrs, the wear of the top end of sleeve being the limiting factor (Poor lubrication?). This was acceptable for aircraft use, but would be a problem in commercial use. In most publications regarding SSV engines, just the Sleeve driving mechanism needed an specially devoted arrangement for lubricating oil supply. Looking in the international patent database Espacenet with the key words sleeve valve you'll retrieve most patents dealing with this kind of engines, all of free download. For example GB patent 305091 and GB288535 by British Continental, and also US2003743 by Fedden, deal with an arrangement for the sleeve driving mechanism; US patents 1820629 and US1814764 by A M Niven and US2319546 by R Insley deal with the method of making sleeves, so does US1820629 and US1814764 by A M Niven; GB555122 by Bristol and US1682702 by H J Edwars is on the coating of sleeves; GB704357 by H Ricardo on the way to make holes in sleeves; GB390434 and 329906 by British Continental are about counterbalancing of sleeves, and so does GB300434 by H Ricardo. GB202262 by Barr and Stroud is about general issues of SVs, and so is GB382571 and CA353554. GB668911 by H Ricardo is about special modifications for small size SV engines, and US2367963 by H Ricardo is about a SV 2-Stroke engine. Some additional discussion on a current SSV engine working unit can be found in YouTube, ChargerMiles007 videos and comments about it. That's all folks! --Jgrosay (talk) 18:43, 29 August 2013 (UTC)

Bristol sleeve-valve engines were assembled using a colloidal graphite solution known as "Dag":[5] — Preceding unsigned comment added by 95.150.10.245 (talk) 16:59, 2 January 2017 (UTC)

For Sleeves working inside an Iron cylinder, Iron was a good enough material, situation was more complex for Aluminum Air Cooled Cylinders, where extensive research about materials and specially hardened Sleeves were required. Sleeves for Knight double S-V engines were machined in a two step way, inside and outer part, the inner part had a plaster cast inside to stabilize it while machining the outer side. Data in article about Diesel S-V engines, 1951, references list.--Caula (talk) 10:47, 5 March 2017 (UTC)

Spelling difference in main arricle page

In the section of history of Sleeve-Valve, a text highlighted in red letters signals the 'Burt-McCollum' type of sleeve valve, this was changed, as originally, it read 'Burt-McCullum' and under this spelling, it send to another Wikipedia cite; the right spelling is 'Burt-McCollum', but as the internal link was orginally written as 'Burt-McCullum' currently the link links to nothig, please, somebody taking care of solving this misspelling, and activating the internal Wikipedia link to the right name 'Burt-McCollum'.--Jgrosay (talk) 11:31, 22 August 2013 (UTC)

In the linked 1939 Flight article in an earlier preceding section it is spelt 'Burt-McCallom'.

The correct spelling is "Burt-McCallom" - from the engineers Peter Burt and Charles McCallom. [6]

James Harry Keighly McCollum (no second e in Keighly either) was a Scot working for Argyll, with Burt, who gained a 1909 patent.[7] This was the Burt-McCollum sleeve valve.

Charles McCallom was a Canadian, of whom nothing is known other than that Flight cite. This may be Flight's mistake. Andy Dingley (talk) 17:31, 2 January 2017 (UTC)

External links modified

Hello fellow Wikipedians,

I have just added archive links to one external link on Sleeve valve. Please take a moment to review my edit. If necessary, add {{cbignore}} after the link to keep me from modifying it. Alternatively, you can add {{nobots|deny=InternetArchiveBot}} to keep me off the page altogether. I made the following changes:

• Added archive https://web.archive.org/20111112180807/http://www.rcvengines.com/pdf_files/saepaper.pdf to http://www.rcvengines.com/pdf_files/saepaper.pdf

When you have finished reviewing my changes, please set the checked parameter below to true to let others know.

This message was posted before February 2018. After February 2018, "External links modified" talk page sections are no longer generated or monitored by InternetArchiveBot. No special action is required regarding these talk page notices, other than regular verification using the archive tool instructions below. Editors have permission to delete these "External links modified" talk page sections if they want to de-clutter talk pages, but see the RfC before doing mass systematic removals. This message is updated dynamically through the template {{source check}} (last update: 18 January 2022).

• If you have discovered URLs which were erroneously considered dead by the bot, you can report them with this tool.
• If you found an error with any archives or the URLs themselves, you can fix them with this tool.

Cheers. —^{cyberbot II}_{Talk to my owner:Online} 22:32, 29 August 2015 (UTC)

I am currently building a sleeve valve two stroke engine which utilises two sleeves in an opposed piston layout. One sleeve controls transfer events and the other exhaust events. The sleeves have no ports and the flow coefficients are high because the port areas are huge (85% of piston crown area). The sleeves are from EN24T and the cylinder liners are from aluminium alloy with nicasil coating inside and out. — Preceding unsigned comment added by Paulfredric (talk • contribs) 12:35, 20 March 2017 (UTC)

Disadvantages?

I feel like some of the statements in the Disadvantages section are Counteractive or ambiguous:
"A serious issue with large single-sleeve aero-engines is that their maximum reliable rotational speed is limited to about 3,000 RPM,  but the M Hewland car engine was raced above 10,000 rpm without toil." - This says that this SSV engine has a sub-par redline, but says that this other SSV engine has a redline that is well above average. So is there a disadvantage or not? Either this should be removed, or rewritten to be more descriptive of this fact.

"Some (Wifredo Ricart, Alfa-Romeo) feared the build-up of heat inside the cylinder, however Ricardo proved that if only a thin oil film is retained and working clearance between the sleeve and the cylinder barrel was kept small, moving sleeves are almost transparent to heat, actually transporting heat from upper to lower parts of the system." - Then if Ricardo proved this is not a problem, this Shouldn't be here! Saying this is an existing disadvantage is blatantly false! This should be removed or moved to the Historical section.

"An inherent disadvantage is that the piston in its course partially obscures the ports, thus making it difficult for gases to flow during the crucial overlap between the intake and exhaust valve timing usual in modern engines. Mike Hewland admitted this was a problem at speeds above 10,000 rpm in his engines aimed at racing, but in the middle range, SSV was always better than a poppet valve engine. The 1954 printing of the book by Harry Ricardo: 'The high-speed internal combustion engine', and also some patents on sleeve valve production, point out that the available zone for ports in the sleeve depends on the type of sleeve drive and bore/stroke ratio; Ricardo tested successfully the 'open sleeve' concept in some two-stroke, compression ignition engines. It not only eliminated the head rings, but also allowed a reduction in height of the engine and head, thus reducing frontal area in an aircraft engine, the whole circumference of the sleeve being available for exhaust port area, and the sleeve acting in phase with the piston forming an annular piston with an area around 10% of that of the piston, that contributed to some 3% of power output through the sleeve driving mechanism to the crankshaft. The German-born engineer Max Bentele, after studying a British sleeve valve aero engine (probably a Hercules), complained that the arrangement required more than 100 gearwheels for the engine, too many for his taste." - So, SSV engines have limited viable cylinder dimensions, but then it mentions how this problem was (somewhat) solved by Ricardo, AGAIN. This Should be moved to the historical section. BUT the part with Max Bentele can stay, highlighting the disadvantage that SSV Engines can become more mechanically complex than conventional engine designs.                                                                                                                            - Now, I would have made these changes myself, but it felt it best to make this a discussion before we make any changes.  — Preceding unsigned comment added by 75.181.151.91 (talk) 01:30, 12 May 2018 (UTC)